This Ghost Fire board project is cursed (but finally coming along nicely); replacing a flaky Line 6 POD GO power switch

First I put together a pedal board to support my NUX MG-300 MKII. I ordered a Ghost Fire Standard 1.0 from Amazon, which USPS routed to Torrance for some reason (30+ minutes away), and it never got here. So Amazon shipped another one, which arrived. Cool. 

Then I needed a volume pedal, as the volume control for the NUX is buried in menus and, patched into the FX RETURN input on my Marshall MG50RCD combo amp, or the AUX IN on the back of my Roland MicroCube (which runs perfectly hanging off the DC output from the ISO Power Block, I had no volume control on the amp. I ordered a HOTONE on sale. That was also routed by USPS to Torrance. (?!?!) So Amazon sent out another one. That one went out UPS, though the tracking number Amazon provided has never been recognized by the UPS website. Amazon’s own tracking shows only “carrier delay” in Lodi (half a state away), 11 days ago, no update since then. So they sent another one! That one finally arrived.

Then as I got into working with the NUX I realized I needed more control than it provided. The two foot switches could go up/down between presets, between scenes within a preset (e.g., to toggle on/off overdrive), or in “hybrid” mode, you can go up (only) on the preset, and cycle 1/2 or 1/2/3 (depending on configuration) on the scenes, but then you had no way to go down a preset. Which could work if you’re playing a static set list and never accidentally overshoot, but in a rehearsal when you don’t necessarily know what song you’re going to play next, cycling all the way through the dozens of presets isn’t ideal. So maybe then you’re leaning over to work the non-footswitch controls, with a guitar hanging off your shoulder, in a cramped rehearsal space - not ideal. Anyway. I looked at the MG-400 (which has dedicated preset up/down foot switches, plus two CTRL foot switches at least one of which could be set to SCN to cycle through scenes), and the MG-30 (which has three foot switches I could set up the way I wanted), but by that point you’re getting really close to used pricing on some much better gear...

I found a Line 6 POD GO Wireless on Guitar Center’s website in what was reported to be good condition, for a good price:

The Line 6 POD GO Wireless in question
The Line 6 POD GO Wireless in question

Ordered it. The photos clearly show it with a power supply. It arrived without a power supply. GuitarCenter gasped when they saw the price point of the Line 6 DC-3i power supply (9V⎓3A), $60, but to their credit sent it immediately - but they did so via economy shipping. Another week...

I found a $15 generic one on Amazon that would arrive the next day (yesterday). Ordered it to start using the board, and to have as a backup. Amazon claims they were unable to access my location, though everyone else’s Amazon packages arrived. Whatever. It finally arrived today. It works. The unit boots. But the power switch is flaky - a known issue with these, apparently. One guy decided to bypass it by soldering in a jumper wire. Others say spraying in DeoxIt cured the issue, but it didn’t on mine. (Also, apparently the switches under the footswitch actuators need replacement from time to time? Instructions with part number.) Anyway, it’s bad. It’s so bad, just plugging in the bundled Relay G10TII transmitter to charge it is enough to knock the switch connection loose and (at best) cause the unit to reboot (typically it just dies and you have to kind of wiggle the switch to get it to come back online).

I’m going to bypass it, probably with spade connectors rather than soldering onto the PCB. I maybe should just return the thing (45 day return policy), but no guarantee another one won’t be just as bad, this one’s otherwise in good shape, and I’m not spending $700 + tax on a new one... Update: None of the spade connectors I have are the right size. I rigged it to work...

The two wires from the power switch bridged with a two barb connector, definitely not a recommended solution!
Used to call this shade tree engineering

.. and I’m going to try this Micro Traders 2pcs 2Pin Slim Rocker Switch 6A 250V 2 Position Power Switch RL3-4T125/55 as a replacement for the stock switch, RLEIL RL3-4T125/55, marked 6C2JA 250V~ 1E4, 10A 125V~T105:

The OEM power switch
RLEIL RL3-4T125/55

(I found the exact RLEIL switch on eBay but they’re all shipping from China.) The switch is a simple two connector design that just presses into the back panel of the Line 6 and snaps into place; need to remove the base plate to pop it out, but you can connect a replacement and snap it into place without disassembly.

Then, the included G10TII transmitter wasn’t charging and was flashing orange/red red red red (though it showed as charging on the POD GO main screen). It also didn’t show up in Line 6 Updater for firmware updates (some folks reported a firmware mismatch could stop the transmitter from charging properly). DeoxIt did cure that, I think. At least I could now see the transmitter in the Updater application and was able to update its firmware (now running 2.06 from July 2024; the GO is running 2.50 from January 2025). After twenty minutes plugged into the GO, the G10TII finally has a green charge light. (It was connected for hours before and never took a charge.)

Next, I wanted to hang a couple of D-type TRS connectors under the pedal board. I found the perfect part, but it’s in the UK and they’re not currently shipping to the U.S. The proprietor was great and checked to see if it made sense to do a one-off but with the import duties / fees / etc., it really just didn’t. There’s an American source for a similar part, but it’s taller and would be uncomfortably tight, and with shipping was like $47, so, no. I had ChatGPT throw together an STL file and ordered that, along with another G10TII holder for a guitar strap, from the same place I ordered from before.

Stay tuned...

Update: I asked the Warwick folks if I could bridge the two 9V⎓500mA outputs, and the two variable outputs that can be configured to supply 9V⎓500mA, into a 9V 2A supply¹. (Their materials say this works with other Power Block models, though stress it’s not a supported configuration.) Their response was noncommittal but they didn’t warn me against it: “It’s theoretically possible but you won’t know for sure that it will work for your needs until trying it. As that document says we don’t officially endorse that method, but others have tried it and had some luck.” So I tried it. I used this DC Splitter Cable 1 Female to 4 Male, Pure Copper 4 Way 5.5mm x 2.1mm Cable ($5) and this 5.5mm x 2.5mm Male Plug to 5.5mm x 2.1mm Male Adapter Connector Cable ($8.50), hooked it up (with my jury-rigged power switch bypass still in place), and lo and behold, it works! Boots up and I ran through a bunch of the factory presets, while using the wireless system, no hiccups whatsoever. Sweet.

ISO Power Block 6 IEC powering POD GO Wireless with bypassed power switch
ISO Power Block 6 IEC powering POD GO Wireless with bypassed power switch

I love it when a plan comes together

I used some heat shrink tubing and a heat gun to label the DC5521 ⇔ DC5525 cable as such, with a crude arrow pointing to the 2.5 mm end. I removed the feet from the Line 6 and attached Velcro, with matching strips on the Ghost Fire. I added an inexpensive single footswitch Bluetooth page turner to the board: One tap forward, double tap back; there was only really room for a single foot switch once the Line 6 was installed. (I should probably have sprung for the $75 STOMP Mini, but this was about $25, and so far seems to work well enough). I started tidying up the wiring. The 3D printed pieces arrived today (10/29), so time to install those as well. I picked up a Bambu A1 Mini at Target because it was on sale ($199, same extended Black Friday the manufacturer announced, and I get another 5% off after that), and was in stock at the store down the street; $232 (including $18.99 for a kilogram of SLA filament) and I’ve joined the ranks of 3D home printers.

“Label” added to DC5521/DC5525 cable
“Label” added to DC5521/DC5525 cable

Velcro applied to Line 6 POD Go with feet removed
Velcro applied to Line 6 POD Go with feet removed

Replacing the Line 6 POD Go Power Switch

The switch I found on Amazon ($8 for a two pack) plugged right in and snapped into place perfectly. Huzzah. It’s not an identical part to the one installed at the factory, but I checked with a friend of mine who works at Line 6 who confirmed my suspicion - even a 125V⎓6A switch is overkill when the power input is 9V⎓3A (er, 2A in this installation).

New switch connected to existing wiring
New switch connected to existing wiring

New switch works perfectly
New switch works perfectly

With the Line 6 installed on the board, the Ghost Fire still fits in the carrying case it came with. Score. So far the front pocket is going to be carrying 2x instrument cables (one to connect to the amp, the other a backup to the wireless setup), an IEC to NEMA power cable, and ... We’ll see. Lately we always seem to need a way to patch a laptop or phone into the PA system, so maybe this $20 FiiO BTR11 Bluetooth receiver and this Apple USB C to 3.5 mm dongle, and a Monoprice 1/8" TRS to 1/4" TRS cable for my home jamming with the Line 6 (you can switch the effects return, which I’m not using, to be an AUX input). Finally, a long USB C to USB B cable to conveniently program the Line 6, and the little charging cable that came with the page turner. Oh, and a pair of TRS to XLR adapter cables, for FOS / FRFR hookup (remembering to change the outputs to line level³).

Mounting the TRS connectors

I drilled out two holes with a 1/8" drill bit and used M4x16 screws to mount the 3D printed Neutrik D-type Patch Panel². Mounted these: D-Type Panel 1/4" 6.35MM Female to 6.35MM Male Stereo Jack Cable TRS Female Solderless Wall Plate to 1/4 Male Cable 60CM. Had to use a pair of needle nose pliers to hold the nuts, and it was kind of tight, but I got it done. All things considered, think it turned out nicely:
TRS jacks mounted on 3D printed plate
TRS jacks mounted on 3D printed plate

Wireless transmitter holder

Went back to the same well and had the STL file printed again for this rig. Fits like a glove, just like before. This time I’m using this Right Angle Guitar Extension Cord which seems to work just fine (although there are some scathing 1-star reviews; again, time will tell).

DC Out

My final tweak will be to 3D print the “circle hole cover” STL file with a 20mm hole centered to mount this pass-through connector. (Now that I can whip up my own custom 3D prints, I might have been tempted to go with something like this instead. But I already have the other. Next build, maybe.) Anyway, this will be patched to the Power Block and provides a convenient power source for the MicroCube, with a 6' long DC cable.

_____

¹ Line 6 recommends their 3A supply, the unit itself says it needs 2.5A, but there’s a lot of community discussion (ex. a, ex. b) and even one post from CIOKS, that establishes it doesn’t draw anywhere close to that.

² Actually, 1 and 1/2 screws; one broke off when I was trying to self-tap it into a smaller hole 😑. Enough of it is sticking out of the hole that it provides lateral stability, and the other screw seems to hold it vertically in place well enough. We’ll see how it goes. This whole board has been ... a learning experience.
 
³ Press and hold both Page < and Page > buttons to open the Global Settings menu, then turn the second encoder knob so that Line is selected for the Main Outputs. 

Comments